Thingmagic Autonomous Configuration Tool Uživatelský manuál Strana 1

1Autonomous Configuration Tool User GuideVersion 1.0 - Supported Hardware: • Micro (firmware v1.5 and later)875-0076-01 RevA

Installing ACTAutonomous Configuration Tool v1.0 User Guide 10Linux 1. Go to the directory created from extracting the zip archive2. Right-click on th

Starting ACTAutonomous Configuration Tool v1.0 User Guide 11Starting ACTMain WindowUpon starting up ACT you will see the Home screen as shown in Figur

Starting ACTAutonomous Configuration Tool v1.0 User Guide 12In addition to the main tabs providing access to different functionality, additional infor

ConnectAutonomous Configuration Tool v1.0 User Guide 13ConnectThe Connect tab provides connection options to find and connect to a reader. Please refe

ConnectAutonomous Configuration Tool v1.0 User Guide 14NoteThe baud rate value set here will be the value saved to the module when the settings are ap

ConfigureAutonomous Configuration Tool v1.0 User Guide 15ConfigureAfter a successful Connect to a reader the Configure tab, as shown in Figure 3, prov

ConfigureAutonomous Configuration Tool v1.0 User Guide 16Table 1: Read & Write Settings Setting DescriptionProtocols The protocols supported by th

ConfigureAutonomous Configuration Tool v1.0 User Guide 17Performance Tuning OptionsThis section provides a set of options, based on high-level usecase

ConfigureAutonomous Configuration Tool v1.0 User Guide 18Save ProfileOnce connected to a reader the desired autonomous configuration of the reader, in

ConfigureAutonomous Configuration Tool v1.0 User Guide 19NoteThis utility can be used to downgrade firmware also.AboutThis section displays firmware v

2Government Limited Rights Notice: All documentation and manuals were developed at private expense and no part of it was developed using Government fu

ReadAutonomous Configuration Tool v1.0 User Guide 20ReadOnce an autonomous configuration has been applied and youʼve chosen to start reading you can u

ReadAutonomous Configuration Tool v1.0 User Guide 21Timestamp - The timestamp when the tag was last seen during this query.RSSI - The receive sign

Processing Data from the ReaderAutonomous Configuration Tool v1.0 User Guide 22Processing Data from the ReaderSample Response Processing CodeStrictly

Processing Data from the ReaderAutonomous Configuration Tool v1.0 User Guide 23Message Types Sent By ReaderWhen operating in autonomous mode there are

Processing Data from the ReaderAutonomous Configuration Tool v1.0 User Guide 24Message ExampleA sample Tag Read Data message with no embedded read dat

Processing Data from the ReaderAutonomous Configuration Tool v1.0 User Guide 25Temperature Status MessageA Temperature Status Message will be returned

Processing Data from the ReaderAutonomous Configuration Tool v1.0 User Guide 26Read-Cycle Reset/Keep-AliveThe Read-Cycle Reset/Keep-Alive message are

Processing Data from the ReaderAutonomous Configuration Tool v1.0 User Guide 27CCITT CRC-16 CalculationThe same CRC calculation is performed on all me

TroubleshootingAutonomous Configuration Tool v1.0 User Guide 28TroubleshootingTroubleshooting See the Troubleshooting section of the ACT Help tab.Coll

3 ContentsIntroduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5Autonomous Readin

4Processing Data from the Reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22Sample Response Processing Code. . . . . .

Autonomous Configuration Tool v1.0 User Guide 5 Autonomous ConfigurationTool v1.0User GuideIntroductionThis document explains how to use the Autonomo

Autonomous Reading OverviewAutonomous Configuration Tool v1.0 User Guide 6Autonomous Reading OverviewAutonomous operation allows the reader to be conf

Autonomous Reading OverviewAutonomous Configuration Tool v1.0 User Guide 7USB I/O Specific NotesWhen connected via the USB interface the reader will

Usage WorkflowAutonomous Configuration Tool v1.0 User Guide 8Usage WorkflowOnce ACT is installed, see Installing ACT section for details, this documen

Installing ACTAutonomous Configuration Tool v1.0 User Guide 9Installing ACTThe Autonomous Configuration Tool is available for 32-bit and 64-bit Linux